Microscale Hardness of Acidic Electroless Ni-P/Ni-P-SiC Nano Composite Depositions

Authors

  • Munna Ram Department of Physics, Graphic Era (Deemed to be University), Dehradun, Uttarakhand, India
  • Moh. Abdul Aleem Ansari Department of Physics, Graphic Era (Deemed to be University), Dehradun, Uttarakhand, India
  • Awanish Kumar Sharma Department of Physics, Graphic Era (Deemed to be University), Dehradun, Uttarakhand, India
  • Sulaxna Sharma Department of Chemistry, THDC Institute of Hydropower Engineering and Technology, Tehri, Uttarakhand
  • Vipin Choudhary Department of Physics Gurukul Kangri University, Haridwar, India

Keywords:

Coatings, Electroless, Ni-P-SIC, SEM, EDAX, Hardness.

Abstract

The ELNi-P along with Ni-P-SiCnano-composite coatings were plated on mild steel (AISI1040) substrates
effectively. The ultrafine SiC particles with nano-size range of 50-70 nm as second phaseparticles were co-
incerted intoan acidic electroless Ni-P bath. The SiC nano-particles of 4 gpl concentration were used for co-
deposition into an EL Ni-P bath. The sodium hypophosphite particularly is selected as a reducer in chemical
reactions. After two hours completion of platings, the as-coated EL Ni-P/Ni-P-SiC platings were heat treated at
400C in argon (Ar) environment for lone one hour period. As coating time increases thickness of coating also
increases. The thickness of coating for all samples is found in between of range 20 to 25 micrometer. Further the
micro-structure along with micro-hardness of as-deposited and heated coupons and were investigated for surface
morphology by FESEM and EDAX respectively. The randomly dispersal of SiC nano-particles into the EL Ni-
P-matrix is shown for 4gpl by micro-structural results. Insertion of ultrafine SiC particles into Ni-P matrix, it
appears that size of Ni/Ni-P grainthroughout plating process reduced and introverted the grain growth for the
period of the heat treatment. The micro-hardness at HV30 scale was improved significantly by adding up of
especially SiC nano-particles into acidic Ni-P electroless bath after heated at 400 C for time of one hour. The
increment in hardness of Ni-P-SiC nano-composite coatings against Ni-P coating is explained

Downloads

Download data is not yet available.

References

Agarwala, R. C. (1987). Structural studies and crystallization behaviour of electroless Ni-P films. Ph.D. Thesis,

University of Roorkee, Roorkee (India).

Agarwala, R. C., & Agarwala, V. (2003). Electroless alloy/composite coatings: A Review.Sadhana, 28(3-4),

-493.

Apachitei, I., Tichelaar, F. D., Duszczyk, J., & Katgerman, L. (2002). The effect of heat treatment on the

structure and abrasive wear resistance of autocatalytic NiP and NiP–SiC coatings. Surface and Coatings

Technology, 149(2-3), 263-278.

Journal of Graphic Era University

Vol. 8, Issue 2, 71-77, 2020

ISSN: 0975-1416 (Print), 2456-4281 (Online)

Balaraju, J. N., Anandan, C., & Rajam, K. S. (2005). Morphological study of ternary Ni–Cu–P alloys by atomic

force microscopy. Applied Surface Science, 250(1-4), 88-97.

Brenner, A., & Riddell, G. (1946). Nickel plating on steel chemical reduction. U. S. Department of Commerce

National Bureau of Standards, 37, 31.

Brenner, A., & Riddell, G. (1947). Nickel plating on steel by chemical reduction. U. S. Department of

Commerce National Bureau of Standards, 39(5), 385.

Datta, P. K., Bedingfield, P. B., Lewis, D. B., & Wells, P. B. (1991). Structure and phase changes

accompanying treatment of electroless Ni–B alloy coating. Conference Proceeding 2nd International Electroless

Nickel Conference Solihull, 139–153.

Mallory, G. O., & Hajdu, J. B. (1990). Electroless plating: fundamentals and applications. American

Electroplaters and Surface Finishers Society, Orlando, Florida, (Eds.) 269.

Huang, Y. S., Zeng, X. T., Hu, X. F., & Liu, F. M. (2004). Corrosion resistance properties of electroless nickel

composite coatings. Electrochem. Acta, 49(25), 4313–4319.

Jiaqiang, G., Lei, L., Yating, W., Bin, S., & Wenbin, H. (2006). Electroless Ni-P-SiC composite coatings with

superfine particles. Surf. Coat. Technol, 200(20-21), 5836–5842.

Sharma, S., Saini, C. K., & Sharma, S. (2014). To develop the electroless NiP-ZnO coating on glass substrate by

electroless. Technique Journal of Materials and Environmental Science, 5(5), 1667-1670.

Srivastava, A., Mohan, S., Agarwala, V., & Agarwala, R. C. (1992). Factors influencing the deposition rate of

Ni-B electroless films. Zeitschrift fur Metallkunde. 83(4), 251-253.

Sudagar, J., Lian, J., & Sha, W. (2013). Electroless nickel, alloy, composite and nano coatings–A critical

review. Journal of Alloys and Compounds 571, 183-204.

Wang, S. C., & Wei, W. C. J. (2003). Characterization of electroplated Ni/SiC and Ni/Al2O3 composite

coatings bearing nano particles. Journal of Materials Research, 18(7), 1566-1574

Downloads

Published

2023-02-28

How to Cite

Ram, M., Ansari, M. A. A., Sharma, A. K., Sharma, S., & Choudhary, V. (2023). Microscale Hardness of Acidic Electroless Ni-P/Ni-P-SiC Nano Composite Depositions. Journal of Graphic Era University, 8(2), 71–77. Retrieved from https://riverpublishersjournal.com/index.php/JGEU/article/view/44

Issue

Section

Articles