Slip and No Slip Conditions in Serpentine Channel for Bingham Fluid-Numerical CFD Investigation

Authors

  • Kuldeep Panwar General Electric Power, Noida, India

DOI:

https://doi.org/10.13052/jgeu0975-1416.1114

Keywords:

Serpentine channel, CFD, non-newtonian channel, slip and no slip

Abstract

For the flow of a Bing-ham fluid in a serpentine tube with a circular cross section, a numerical examination of slip and no slip scenarios was conducted. This was done in order to better understand the flow. This investigation was carried out. In order to get a deeper comprehension of the flow behavior, several flow situations, including slip and no slip, are investigated using separate sets of parameters. In order to solve the issue presented by the turbulent model, the K-model is put to use. It was discovered that the parameter variation for no slip circumstances is preferable to that of no slip scenarios under high stress. This was discovered by comparing the two. A limited analysis of the flow behavior of the Bingham fluid in a serpentine cannel served as the impetus for the current work. The research that was done was motivated by this analysis.

Downloads

Download data is not yet available.

References

Bigyani Das, Flow of Bingham fluid in a slightly curved tube (1992), International Journal of Engineering Science Vol. 30, No. 9, pp. 1193–1207.

Bayazitoglu, Paslay and Cernocky, Laminar Bingham fluid flow between vertical parallel plates (2007) international journal of thermal science 46 (2007) 349–357.

Fusi and farina, flow of Bingham fluid in non-symmetric inclined channel (2016), journal of Non-Newtonian Fluid Mechanics, JNNFM3783.

Mukherjee, Gupta and Chhabra, Laminar forced convention in power law and Bingham plastic fluids in ducts semi-circular and other cross sections, (2016) International Journal of Heat and Mass Transfer 104 (2017) 112–141.

Shelukhin and Neverov Thermodynamics of micropolar Bingham fluids (2016), journal of non-Newtonian fluid mechanics, JNNFM 3826.

Skelland, Non-Newtonian Flow and Heat Transfer. Wiley, New York (1967).

S. N. BARUA, Q. J. Mech. Appl. Math. 16, 61 (1963).

Kreith, the CRC Handbook of Thermal Engineering, CRC Press, Boca Raton, FL,2000.

Q.M. Lei, A.C. Trupp, Maximum velocity location and pressure drop of fully Develop laminar flow in circular sector ducts, ASME J. Heat Transfer 111 (1989) 1085–1087.

C.Y. Wang, Flow through a lens-shaped duct, ASME J. Appl. Mech. 75 (2008) 034503–034503-4.

Panwar, K, Murthy, D, S, “Analysis of thermal characteristics of the ball packed thermal regenerator”, Procedia Engineering, 127, 1118–1125.

Panwar, K, Murthy, D, S, “Design and evaluation of pebble bed regenerator with small particles” Materials Today, Proceeding, 3(10), 3784–3791.

Bisht, N, Gope, P, C, Panwar, K, “Influence of crack offset distance on the interaction of multiple cracks on the same side in a rectangular plate”, Frattura ed IntegritàStrutturale” 9(32), 1–12.

Panwar, K, Kesarwani, A, “Unsteady CFD Analysis of Regenerator”, International Journal of Scientific & Engineering Research, 7(12), 277–280.

Singh, I., Bajpai, P. K., & Panwar, K. “Advances in Materials Engineering and Manufacturing Processes.

Downloads

Published

2023-03-07

How to Cite

Panwar, K. (2023). Slip and No Slip Conditions in Serpentine Channel for Bingham Fluid-Numerical CFD Investigation. Journal of Graphic Era University, 11(01), 45–56. https://doi.org/10.13052/jgeu0975-1416.1114

Issue

Section

Articles

Most read articles by the same author(s)