The Design Process for a Closed Combustion Chamber Flow Blurring Nozzle

  • Radom Pongvuthithum Department of Mechanical Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai, 50200 Thailand
  • James Moran Department of Mechanical Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai, 50200 Thailand
  • Tanakarn Sankui Department of Mechanical Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai, 50200 Thailand
Keywords: Flow blurring nozzle, Stable combustion, Meso scale combustion system, Nozzle design


This research outlines a process whereby a flow blurring nozzle is optimized for use in a meso-scale combustion chamber. Flow blurring is defined as the generation of small turbulence scales in a liquid from a singular back-flow pattern of a gas. Flow blurring nozzles are beginning to be adapted in many technical applications, from emission spectrometry of heavy metals in biodiesel, vaporization of high viscosity fuels to meso-scale combustion applications. This nozzle can vaporize liquids at low flow rates efficiently and inexpensively. It uses an air stream to break up the liquid but it operates in a novel flow blurring regime differentiating it from a regular air blast atomizer. There are two issues with using this nozzle for combustion applications. The first is that the air used to vaporize the hydrocarbon in the flow blurring nozzle is insufficient to burn all the hydrocarbon and it is difficult to increase this air supply. The second issue is that the vaporized mixture at the exit of the flow blurring nozzle has a relatively high velocity. The mixture velocity must be decelerated to enable stable combustion without blowoff. This article outlines the design process for solving both these issues. In total, five design iterations were implemented before a satisfactory final design was achieved.


Download data is not yet available.


V. Sadasivuni and A.K. Agrawal, “A novel meso-scale combustion system for

operation with liquid fuels,” Proceedings of the Combustion Institute, vol. 32, pp. 3155-

, 2009.

D. Dunn-Rankin, M. Leal Elisangela and D.C. Walther, “Personal power systems,”

Progress in Energy and Combustion Science, vol. 31, pp. 422 - 465, 2005.

J. Moran and R. Pongvuthithum, “Combustion of Gasoline for Meso Scale Combustion

Applications,” Distributed Generation and Alternative Energy, vol. 31, no. 4, pp. 71 - 79,

September 2016.

P.D. Hede, P. Bach and A.D. Jensen, “Two-fluid spray atomisation and pneumatic

nozzles for fluidbed coating/agglomeration purposes: A review,” Chemical Engineering

Science, vol. 63, pp. 3821 - 3842, 2008.

I. Whelan, D. Timoney and W. Smith, “Advanced GDI Injector Control with Extended

Dynamic Range,” in SAE 2013 World Congress & Exhibition, Detroit, 2013.

D.C. Kyritsis, I. Guerrero-Arias, S. Roychoudhury and A. Gomez, “Mesoscale Power

Generation by a Catalytic Combustor using Electrosprayed Liquid Hydrocarbons,”

Proceedings of the Combustion Institute, vol. 29, pp. 965-972, 2002.

A. Ganan-Calvo, “Enhanced liquid atomization: From flow focussing to flowblurring,”

vol. 86, no. 214101, 2005.

L. Jiang and A.K. Agrawal, “Combustion of straight glycerol with/without methane

using a fuel-flexible, low-emissions burner,” Fuel, vol. 136, pp. 177 - 184, 2014.

B.M. Simmons, H.V. Panchasara and A.K. Afrawal, “A comparison of air-blast

and flow blurring injectors using phase doppler particle analyzer technique,” in

Proceedings of ASME Turbo Expo, Orlando, 2009.

I. Kroo and P. Kunz, “Mesoscale flight and miniature rotorcraft development, in Fixed

and Flapping Wing Aerodynamics for Micro Air Vehicle Applications,” in of Progress

in Astronautics and Aeronautics, Salt Lake City, 2001.

A. Epstein and S.D. Senturia, “Macro Power from Micro Machinery,” Science, vol. 276,

no. 5316, pp. 1211-1212, 1997.

N.S. Kaisare and D.G. Vlachos, “A review on microcombustion: Fundamentals,

devices and applications,” Progress in Energy and Combustion Science, vol. 38, no. 3, pp.

-359, 2012.

G. Alessandro, J.B. Jonathan, R. Subir, C. Bruno and H. James, “From jet fuel to

electric power using a mesoscale, efficient Stirling cycle,” Proceedings of the Combustion

Institute, vol. 31, p. 3251-3259, 2007.

V. Shirsa and A. Gupta, “A review of progress in heat recirculating meso-scale

combustors,” Applied Energy, vol. 88, no. 12, p. 4294-4309, 2011.